INNOVA ABS

DLG-APPROVED: “Resistance to ammonia, cleaning distance”

Download print version

Test report 7520

The approval

A test mark “DLG-APPROVED for individual criteria” is awarded for agricultural products which have successfully fulfilled a scope-reduced usability testing conducted by DLG according to independent and recognized evaluation criteria. The test is intended to highlight particular innovations and key criteria of  the test object. The test may contain criteria from the DLG test scope for overall tests, or focus on other value-determining characteristics and properties of the test subject. The minimum requirements, test conditions and procedures as well as the evaluation bases of the test  results will be specified in consultation with an expert group of DLG. They correspond to the recognized rules of technology, as well as scientific and agricultural knowledge and requirements. The successful testing  is concluded with the publication of a test report, as well as the awarding of the test mark which is valid for  five years from the date of awarding. 

The ammonia resistance test was performed as a laboratory test according to the patented DLG test standard. This test is intended to determine the suitability of equipment for animal living areas to withstand the impact of animal environments. The cleaning distance test assesses the suitability for cleaning animal living areas. Other critera have not been assessed.

Assessment in brief

The LED light “INNOVA ABS”  from TREVOS, a.s. has successfully com­pleted the DLG test for ammonia resistance and cleaning distance.

According to this result, it can be assumed that these luminaires  are resistant to the typical environmental conditions of animal living areas and that no accelerated reduction of the product lifetime will occur.

In addition, the LED light  “INNOVA ABS” was operated actively in the chamber for the entirety of the test. No product damage was observed here. Furthermore, the cleaning  distance is regarded as suitable for the cleaning of animal houses. 

Table 1:  Overwiew of results:
 

DLG QUALITY PROFILEEvaluation**                               
Ammonia resistance

■■■■

Preservation of the luminous flux

■■■■

Cleaning distance

■■■■


* The DLG test framework provides the following options in its evaluation schemes:  
 ■ ■ or better = meets, exceeds or clearly exceeds the specified DLG standard, ■ ■ = meets the legal re­quire­ments for marketability,   = failed

 

The product

Description and technical data

The tested LED light “INNOVA ABS” is suitable for any usage in animal housing surroundings.
 

Table 2: Technical data (according to manufacturer)

 

INNOVA

 

1.4ft ABS / NB ABS / WB ABS

 

1.5ft ABS / NB ABS / WB ABS

Electrical connection

 

 

 

Voltage

 

230 V

 

Frequency

 

50-60 Hz

 

Performance

20.1 ... 52.8 W

 

25.3 ... 64.7 W

Dimension and weight

 

 

 

Length

1.175 mm

 

1.455 mm

Width

 

90 mm

 

Height

 

93 mm

 

Weight

1,6 kg

 

1,9 kg

Additional technical data

 

 

 

Additional technical data

 

1 / 2

 

Material

 

diffuser: ABS, body: dark grey ABS

 

Colour temperature

 

3.000 / 4.000 / 5.000 / 6.500 K

 

Dimmable

 

yes, Dali (optional)

 

Light angle

 

lambertian / narrow / wide beam

 

Rated luminous flux

 

2.870 ... 10.470 lm

 

The method

Resistance to ammonia

The ammonia resistance of the LED light “INNOVA ABS” was determined by a laboratory test with one luminaire according to the patented DLG test standard for agricultural use. The laboratory test is designed to replicate the conditions of a usage period of about 10 years exposure to animal living areas. 

The test was carried out in a climate chamber under the following climate conditions:

Test duration1500 h
Air temperature70 °C
Relative humidity70 %
Ammonia concentration750 ppm

For assessing the ammonia resistance, each luminaire was examined visually, gravimetrically and the plastic parts additionally through measurement of the hardness (Shore D) before and after the climate testing. Since 2017, luminaires have additionally been following a cycle of operation predefined by DLG (3 hours on, 1 hour off) in order to eveluate any thermal impacts caused by switch-on and -off procedures during ammonia fumigation.

In order to avoid overheating (> 70 °C), the luminaires could be operated at a reduced power level during the testing period.
 

Table 3: Test conditions cleaning distance

Line pressure~150 bar
Watercold, approx. 1,000 l/h, no detergents
Nozzle typeFlat spray nozzle, 25°
Exposition time1 minute
Distance250 mm, 200 mm, 150 mm, 100 mm, 50 mm
Ambient temperature10°C

For all test procedures, the LED light “INNOVA ABS” in length of 1,455 mm has been used. After the tests, the luminaires underwent visual examination to a reference sample that was identical in construction.

The test results in detail

Resistance to ammonia

Visual test

The comparative visual examination after the ammonia exposure has shown minor discolorations at the 
luminaire housing.

During the test, the tube light appeared to be sufficiently gas-tight. Nevertheless it cannot be ruled out, that a limited ammount of ammonium compounds could enter the luminaire housing. Again, no negative impact on the luminaire performance needs to be expected.

The defects are rated as insignificant. The examination of the manufacturer’s mounting parts didn’t also show any defects.

Gravimetric test

Weight comparisions before and after the ammonia fumigation have not shown any measurable increases 
or decreases in weight.

Hardness test

During the hardness test (Shore D) no measurable changes were observed. All determined changes were within the measurement incertainty.

Functional test

No defects were observed. All luminaires worked after the conducted tests.

Preservation of the luminous flux

After completion of the test the luminaire still had a luminous flux of 87.5 %.
 

Cleaning distance

Even at a cleaning distance of only 10 cm, no damages to the luminaire could be observed.  At no time a water ingress into the luminaires was noticed.  In order to avoid damage to the luminaires during cleaning reliably, according to the manufacturer’s specifications a minimum cleaning distance of 10 cm should always be ensured.

Based on the results of these tested parameters, the luminaire is evaluated as resistant to ammonia.

Summary

The results show that the LED light “INNOVA ABS” fullfills the testing requirements for ammonia resistance and cleaning distance and thus receives the test mark DLG Approved. It can be expected that the luminaire is resistant to ammonical air in animal living areas and that no accelerated reduction of the product lifetime occurs.

The LED light “INNOVA ABS” was operated both passively and actively during the ammonia fumigation in the test chamber and passed both tests successfully.

It is also recommended in any case to keep a minimum distance of 10 cm during cleaning.

Applicant and test implementation

Manufacturer and applicant

TREVOS, a.s.
Nová Ves 34
51101 Turnov
Czech Republic

Contact

Phone +420 481 363 311
Telefax +420 481 624 681
TREVOS@TREVOS.cz 
https://TREVOS.eu/en/ 

Test implementation

DLG TestService GmbH, Gross-Umstadt location
The tests are conducted on behalf of DLG e.V.

DLG test framework
DLG Approved Test “Ammonia resistance” 
(current as of 03/2021)

Department
Farm Inputs

Head of Department
Dr. Michael Eise

Test engineer(s)
Dipl-Ing (FH) Tommy Pfeifer *

Photometric laboratory
Photometrik GmbH, Einsteinstraße 24
64859 Eppertshausen, Germany

*    Author