Download print version
Test report 7023
The approval
A test mark „DLG-APPROVED for individual criteria“ is awarded for agricultural products which have successfully fulfilled a scope-reduced usability testing conducted by DLG according to independent and recognized evaluation criteria. The test is intended to highlight particular innovations and key criteria of the test object. The test may contain criteria from the DLG test scope for overall tests, or focus on other value-determining characteristics and properties of the test subject. The minimum requirements, test conditions and procedures as well as the evaluation bases of the test results will be specified in consultation with an expert group of DLG. They correspond to the recognized rules of technology, as well as scientific and agricultural knowledge and requirements. The successful testing is concluded with the publication of a test report, as well as the awarding of the test mark which is valid for five years from the date of awarding.
The DLG Approved Test “Deformability/Elasticity, Permanent Tread Load” includes technical measurements on test stands of the DLG Test Center. The deformability and elasticity, the acid resistance, were measured and a permanent tread load was applied. The test was based on the DLG Testing Framework for elastic stable flooring, current as at April 2010. Other criteria were not investigated.
Assessment – Brief Summary
The Promat Pack Mat with Sand, an elastic floor for deep bedding cubicles in cubicle houses, was investigated with regard to durability and comfort properties on test stands in the DLG Approved Test. The deformability and elasticity were measured and a permanent tread load was applied.
Table 1: Overview of results
| Test characteristic | Test result | Evaluation* |
|---|---|---|
| Deformability and elasticity | ||
| – in new condition | 40.7 mm, very good | + + |
| – following endurance test | 28.8 mm, very good | + + |
| Permanent tread load | no noticeable wear | |
| clear lasting deformation of the hoses filled with rubber granulate | – | |
| + |
* Evaluation range:: + + / + /◯ / – / – – (¡ = Standard)
** Evaluation range: + = resisitant / ◯ = limited resistant / – = not resisitant
The product
Description and specifications
The Promat Pack Mat with Sand tested here, an elastic floor for deep bedding cubicles in cubicle houses
- total heigh: approx. 110 mm
- underlay
– thickness: approx. 50 mm
– made of hoses filled with rubber granulate
– tan top cover (approx. 3 mm tick) - sand filling: approx. 60 mm
- seamless installation
The method
Deformability and elasticity
The deformability is measured in new condition and following permanent tread load with a round steel foot (diameter of 105 mm and therefore a contact area of 75 cm²) and a penetration force of 2,000 N (corresponding to approx. 200 kg).
Permanent tread load
The permanent tread load is carried out on a test stand with a round steel foot in the standard test programme with 100,000 alternating loads at 10,000 N (corresponding to approx. 1000 kg). The steel foot is adapted to the natural conditions as an “artificial cow foot”.
The foot has a diameter of 105 mm and therefore a contact area of 75 cm²; the carrying edge of the hoof is simulated by a 5 mm wide ring on the periphery of the sole that projects 1 mm above the rest of the surface. To simulate the daily maintenance of the box the sand was continuously smoothened during the test.
The test results in detail
Deformability and elasticity
In the ball penetration tests in new condition with a calotte (r = 120 mm), penetration depth was 40.7 mm. The resulting calculated bearing pressure of 6.5 N/cm² indicates a very low load on the carpal joints when lying down and getting up. Elasticity was measured following a permanent tread load exerted by a steel foot (contact area: 75 cm²) with 100,000 alternating loads at 10,000 N. Following the endurance test, the penetration depth of the calotte decreased from 40.7 mm to 28.8 mm. The bearing pressure increased from 6.5 N/cm² to 9.2 N/cm² (see Fig. 2). This means that deformability and elasticity decrease.
Permanent tread load
No noticeable wear was observed following exposure to permanent tread load on a test stand with 100,000 alternating loads at 10,000 N. The hosses filled with rubber granulate were compressed and a lasting deformation of 26 mm was measured. Given an original height of approx. 50 mm, this means that the height of the mattress decreased by about 52 %. Up to 30 % is defined as standard. With a continuously maintenance of the box and bring in additional sand this can be balanced.
Based on test-stand investigations, the criteria tested in this DLG Approved Test evaluate the comfort and durability properties of the Promat Pack Mat with Sand for use in the resting area of deep bedding cubicles in cubicle houses. The tested Promat Pack Mat with Sand met the requirements of the Testing Framework with respect to the investigated criteria.
Manufacturer and Applicant
Promat Inc., 594711 County Rd. 59 South, Woodstock Ontario
Contact
Telephone +519 456 2284,
Fax +519 456 1458,
sales@promatinc.com
www.promatinc.com http://www.kraiburg-belmondo.de
http://www.delaval.com
Test implementation
DLG TestService GmbH, Gross-Umstadt location
The tests are conducted on behalf of DLG e.V.
DLG test framework
DLG Approved Test “Elastic Stable Flooring” (current as of 04/2010))
Department
Indoor operations
Head of Department
Dr. Michael Eise
Test engineer(s)
Dr. Harald Reubold *
* Author
Contact us
DLG TestService GmbH - Groß-Umstadt location • Max-Eyth-Weg 1 • 64823 Groß-Umstadt • Tel: +49 69 24 788-600 • tech@DLG.org