DLG e.V. - Test: Cow Mattress Animattress III

Cow Mattress Animattress III Deformability/Elasticity, Permanent Tread Load, Abrasion, Acid resistance, Cleaning distance

Assessment – Brief Summary

The Animattress III tested here, an elastic floor covering for the resting area in cubicle houses, was investigated with regard to durability and comfort properties on test stands in the DLG Approved Test. The deformability and elasticity of the rubber mat, the abrasion resistance, the acid resistance, the cleaning distance were measured and a permanent tread load was applied.

Scroll table to the right to see full display !

Table 1: Overview of results

Test characteristic Test result Evaluation
Deformability and elasticity *
– in new condition 10.1 mm, good +
– following endurance test 10.7 mm, good +
Permanent tread load
no lasting deformation ++
no noticeable wear +
Abrasion test*
good wear resistance +
Acid resistance**
Feed acid mixture resistant +
Uric acid limited resistant
Sulfurous acid resistant +
Ammonia solution resistant +
Disinfection liquid resistant +
Peracetic acid resistant +
Cleaning distance*
with flat jet nozzle 20 cm
with a coarse dirt remover 45 cm

*    Evaluation range: ++ / + /◯ / – / –– (◯ = standard)
**    Evaluation range: + / –

The Product

Animattress III cubicle mattress

Description and Technical Data

The Animattress III cubicle mattress tested here is an elastic floor covering for use in the resting area of high cubicles in cubicle houses; it has a thickness of approx. 32 mm. Black rubber mat

  • upper side with pebble surface
  • under side with conical knops in two sizes
  • big knops 20 mm high and 29 mm at the bottom and 21 mm at the top
  • small knops 13 mm high and 29 mm at the bottom and 25 mm at the top
  • Shore A hardness: approx. 70
  • laid as single mat

The Method

Deformability and elasticity

The deformability is measured in new condition and following permanent tread load using ball penetration tests with a calotte (r = 120 mm) and a penetration force of 2,000 N (corresponding to approx. 200 kg).

Permanent tread load

The permanent tread load is measured on a test stand with a round steel foot in the standard test programme with 100,000 alter­nating loads at 10,000 N (corresponding to approx. 1,000 kg). The steel foot is adapted to the natural conditions as an “artificial cow foot”. The foot has a diameter of 105 mm and therefore a contact area of 75 cm²; the carrying edge of the hoof is simulated by a 5 mm wide ring on the periphery of the sole that projects 1 mm above the rest of the surface.

Abrasion test

In a standardised abrasion test with 10.000 cycles the top cover was grinded with an emery cloth (granulation 280) and a grinding pressure of 500 N (= 8.1 N/cm2 surface pressure). The friction element was cooled continuous with water to prevent an influence of the generated heat during the abrasion test. The size of the grinded  area was 61,5 cm².

Acid resistance

A permanent dipping test in accor­dance to DIN EN ISO 175:2000 (performance of synthetic material against liquid chemicals) was carried out. Test samples (size 30 mm x 30 mm) were complete dipped in different test liquids for 24 hours and 28 days (room temperature 20° Celsius). In the 28 days test the liquids were changed weekly. After the 28 days the samples were washed with distillate water and dried for 24 hours. Before and after the dipping the weight, the dimensions and the shore hardness (shore A) of the test samples was measured. Additional a visual eva­luation was done for alterations like colour changing, swelling, destruction or crystallisation. All samples were evaluated in comparison to the standard water.

Cleaning distance

In test stand trials with a high pressure cleaner (approximately 145 bar, exposure period 1 minute with a 25° flat jet nozzle and a coarse dirt remover) the distance was measured where no damage occurs.

The Test Results in Detail

Deformability and elasticity

In the ball indentation tests in new condition with a calotte (r = 120 mm), indentation depth was 10.1 mm. The resulting cal­culated bearing pressure of 26.2 N/cm² indicates a still rel­a­tively small load on the carpal joints when lying down and getting up. Elasticity was measured following a permanent tread load exerted by a steel foot (contact area: 75 cm²) with 100,000 alternating loads at 10,000 N. Following the endurance test, the indentation depth of the calotte increased from 10.1 mm to 10.7 mm. The bearing pressure decreased from 26.2 N/cm² to 24.8 N/cm² (see Fig. 2). This means that deformability and elasticity slightly increase.

Evaluation see table 1.

Permanent tread load

Slight wear was observed on the top cover following exposure  to permanent tread load on a test stand with 100,000 alternating loads at 10,000 N. No lasting
deformation was observed.

Evaluation see table 1.

Abrasion test

The abrasion depth after 10,000 ­cycles amounted to 1.0 mm, this corresponds to approximately 3 % of the rubber thickness. Of the ground surface 4.0 grams were rubbed off.

Evaluation see table 1.

Figure 2: Deformability as a function of bearing pressure

Figure 3: Permanent tread load

Acid resistance

The rubber mat was limited resis­tant against Uric acid and resistant against the other test liquids used. The differences in weight, thickness and Shore A hardness between the acid treated and not acid treated samples were minor and lay in the range of water as standard. Against the used liquids the rubber mat seems to be satisfactorily suited for the described use. 

Evaluation see table 1.

Cleaning distance

In test stand trials with a high ­pressure cleaner damage to the cover of the mattress only occurred when a minimum distance of 45 cm (with a coarse dirt remover) and 20 cm (with a flat-jet nozzle) was not kept. For cleaning and disinfection of the floor covering only the cleaning agents permitted by the manu­facturer should be used.

Evaluation see table 1.

Figure 4: Samples after acid resistance test

Figure 5: Determination of the cleaning distance

Scroll table to the right to see full display !

Table 2: Test liquids and results acid resistance

Test liquid concentration result after 24 hours residence time result after 28 days residence time Evaluation
Feed acid mixture
concentrate, pH 2 no changing no changing resistant
Excrement acids
Uric acid saturated urea solution (0,4%) no changing surface with color change limited resistant
Sulfurous acid 5-6 % SO2 no changing no changing resistant
Ammonia solution 32% solution no changing no changing resistant
Disinfection liquid
Barn Disinfection liquid 2%-solution of a product with formic acid and glyoxyl acid no changing no changing resistant
Peracetic acid 3000 ppm no changing no changing resistant

Summary

Based on test-stand examinations, the criteria tested in this DLG ­Approved Test evaluate the comfort and durability properties of the Animattress III for use in the resting area of high cubicles in cubicle houses. The tested Animattress III met the requirements of the testing framework with respect to the investi­gated criteria.

DLG Test Center Technology and Farm Inputs

DLG e.V.
Max-Eyth-Weg 1
64823 Groß-Umstadt
Germany
Tel.: +49(0)69 24 788-611
tech(at)DLG.org

Printable version/Download as PDF

DLG-APPROVED Single value-determining criteria A quality mark “DLG-APPROVED for single value-determining criteria” is awarded to agricultural pro­ducts which successfully passed a smaller-scope DLG usability test according to independent and re­cognized evaluation criteria. The test intends to highlight special innovations and key criteria of the test item. The test can focus on criteria from the DLG testing framework for full tests or on other individual features or qualitative criteria. The minimum requirements, the test conditions and procedures as well as the evaluation guidelines of the test results are determined in consultation with a DLG expert group. They comply with the generally recognized technology rules as well as with scientific and agricultural knowledge and requirements. The successful test concludes with the publishing of a test report and the awarding of a quality mark which is valid for five years following the award date.

The DLG Approved Test “De­for­ma­bi­lity/Elasticity, Permanent Tread Load, Abrasion, Acid resistance, Cleaning distance” includes technical measurements on test stands of the DLG Test Cen­ter. The deformability and elasticity, the abrasion resistance, the slip resistance, the acid resistance, the cleaning distance were measured and a permanent tread load was applied. The test was based on the DLG Testing Framework for elastic stable flooring, as at April 2010. Other criteria were not investigated.

Manufacturer and Applicant

Animat Inc.,
395 Rodolphe Racine,
CA J1R OS7, Sherbrooke Canada

Contakt:
Telephone: 0060 819 821 2091 222
Telefax: 0060 819 821 2879
psavary(at)animat.ca
www.animat.com

Test execution

DLG e.V.,
Test Center
Technology and Farm Inputs,
Max-Eyth-Weg 1,
64823 Groß-Umstadt
Germany

DLG Testing Framework
DLG Approved Test
“Elastic Stable Flooring”
(as at 04/2010)

Field
Indoor operations

Project manager
Dipl.-Ing. Susanne Gäckler

Test engineer(s)
Dr. Harald Reubold  *

* Reporting engineer